1/21/2024 0 Comments Instaling Goldie App![]() How can it be, so I re-did the firmware compilation, I re-flashed it and re-started and no nothing. well every command that I could think of but nope, no mounted board. Linux couldn't mount the board, I reconnected, I connected, I ran lsusb, dmesg, usb-devices. The board went nicely into DFU-mode, it flashed without any troubles, I disconnected it, removed the BT0 jumper and rebooted and. Nothing problematic with that so I flashed the firmware by their suggested commands using dfu-utils. Went to Fysetc:s github and followed the instructions for compiling the klipper firmware. I booted up the linux computer and plugged in the Fysetc Spider v2.2 board. Started then with the electronics, and here I ran into troubles. It then found them so they are defined but need to add anyway again. Then I switched to the laptop, and I had to actually add the printers again. ![]() I added the printers and everything as mentioned above. So, in Mailsail - just choose one of the printers, open the printer.cfg and you will see what instance it has mapped to.Īfter installing the klipper, moonraker and mainsail I switched to my desktop computer and used Chrome to connect to my "klipper"-computer. In that directory you find a config directory and there the printer.cfg. Looking in you home directory (or the directory where you installed klipper/moonraker/mainsail you find a directory with named _data.įor Goldie you find a Goldie_data directory. If you do like me, named the instances with the printer name, you have to go in to the printer.cfg template for the printer so find what the instance is called in Moonraker/Klipper. Installed UBUNTU 22.04 LTS and then run KIAUH for setting up 3 instances of Klipper, Moonraker and then three printers in Mainsail.ġ) If you set a name for instances, Mainsail doesn't show which instances it uses when you add the printer and want to name it. So, as the E3MAX is working, I focused to setup the computer. I can't remember seeing anything about this in the build docs or some of the build videos I watched. Then there was a small transparent plastic thingie which I have no clue what it is for.One is in all steel (?) and the bi-metal but is it copper and titanium or have they cheated? The kit ships with a "E3D V6" hot end.The aluminum parts look good, haven't measured or done any further investigations.The real deal with 3M 468MP adhesive on the bed heater.No Pi included (as I expected) though the BOM on Fysetc sellers page kind of states it (has an "optional" word after but not clearly stating it is not included).I just have scanned through the packages and comparing to other peoples "Unboxing", all seems to be included. Managed by a computer, not a Pi (hard time getting one, and want to control the my other printers from same spot)įurther on, when Goldie has got a couple of hours under its extruder, I plan to extend it further with at least:.Mods that I plan to have in the first setup is: It's name is Goldie, from the golden (well, more yellowish) extrusions that I chose. I also jumped the short path and bought the aluminum kit from Fysetc, if it is working ok I will stay with it, if use it to swap to glass fiber enforced CP-12 which has really interesting temperature coefficients.Īlso, the most important part with precious things, the name! So, after a long time probing the "market", I finally decided to build a Voron 2.4 R2 350 as a base and then do some additional mods. I also have got really cheap a Sovol SV03, which I intend to rebuild to an IDEX, but that's another story. It prints PETG really nice, but life pushes us forward and I want to be able to print more advanced filaments which requires more of an high temperature enclosed printer. I have an Ender 3 Max, modified with dual Z-axes, Sprite 300 C extruder and hotend, PEI-sheet etc. ![]() New to the community with a smoking hot delivery of a Voron 2.4 R2 kit bought from Fysetc via Aliexpress.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |